RAM Ram 2012 Page 84 Owner'S Manual Download | Manualshive

Page: 84 / 173

background image

WARNING! (Continued)

The inlet for the engine air intake is located behind
the passenger side headlamp and receives air
through the grille.

FUEL REQUIREMENTS

Use good quality diesel fuel from a reputable supplier in
your vehicle. Federal law requires that you must fuel this
vehicle with Ultra Low Sulfur Highway Diesel fuel (15
ppm Sulfur maximum) and prohibits the use of Low
Sulfur Highway Diesel fuel (500 ppm Sulfur maximum)
to avoid damage to the emissions control system. For
most year-round service, No. 2 diesel fuel meeting ASTM
specification D-975 Grade S15 will provide good perfor-
mance. If the vehicle is exposed to extreme cold (below
20°F or -7°C), or is required to operate at colder-than-
normal conditions for prolonged periods, use climatized
No. 2 diesel fuel or dilute the No. 2 diesel fuel with 50%

No. 1 diesel fuel. This will provide better protection from
fuel gelling or wax-plugging of the fuel filters.

WARNING!

Do not use alcohol or gasoline as a fuel blending
agent. They can be unstable under certain conditions
and hazardous or explosive when mixed with diesel
fuel.

Diesel fuel is seldom completely free of water. To prevent
fuel system trouble, drain the accumulated water from
the

fuel/water separator using the fuel/water separator

drain provided. If you buy good quality fuel and follow
the cold weather advice above, fuel conditioners should
not be required in your vehicle. If available in your area,
a high cetane “premium” diesel fuel may offer improved
cold-starting and warm-up performance.

82

STARTING AND OPERATING

«
...
82
83
84
85
86
...
»

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments

Related manuals for Ram 2012

Brand: Happy Orange Pages: 2

Brand: Dakota Digital Pages: 2

Brand: Dakota Digital Pages: 7

Brand: Ignition Pages: 1

Brand: Daewoo Pages: 68

Brand: Hyundai Pages: 437

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

Brand: Metra Electronics Pages: 2

Brand: TATA Motors Pages: 156

Brand: Mobile Create Pages: 15

Brand: SCC Pages: 4

Brand: Power Acoustik Pages: 4

Brand: Toyota Pages: 165

MagicSafe MSG150

Brand: Waeco Pages: 20

Brand: Reliant Pages: 116

Brand: Hama Pages: 39

Brand: Whispbar Pages: 34

Brand: Prime Design Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands