RAM Ram 2012 Page 17 Owner'S Manual Download | Manualshive

Page: 17 / 173

background image

INSTRUMENT CLUSTER DESCRIPTION

1. Tachometer

The tachometer indicates engine speed in revolutions per
minute.

CAUTION!

Do not operate the engine with the tachometer
pointer at high RPM for extended periods. Engine
damage may occur.

2. Turn Signal Indicator Light

The arrow will flash with the exterior turn signal
when the turn signal lever is operated.

NOTE:

•

A continuous chime will sound if the vehicle is driven
more than 1 mile (1.6 km) with either turn signal on.

•

Check for an inoperative outside light bulb if either
indicator flashes at a rapid rate.

3. Fuel Gauge

Shows level of fuel in tank when ignition switch is in the
ON position.

4. Temperature Gauge

The temperature gauge shows engine coolant tempera-
ture. Any reading within the normal range indicates that
the engine cooling system is operating satisfactorily.

The gauge pointer will likely indicate a higher tempera-
ture when driving in hot weather, up mountain grades,
or when towing a trailer. It should not be allowed to
exceed the upper limits of the normal operating range.

3

UNDERSTANDING YOUR INSTRUMENT PANEL

15

«
...
15
16
17
18
19
...
»

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments

Related manuals for Ram 2012

Brand: ZAPTEC Pages: 64

Brand: ZAPTEC Pages: 24

Brand: Compass Pages: 16

Brand: Pyle Pages: 4

Brand: Whispbar Pages: 14

Brand: Jeep Pages: 136

Brand: Hella Pages: 21

Brand: Meta System Pages: 22

Brand: Yakima Pages: 12

Brand: Axxess Pages: 16

Brand: Ranger design Pages: 24

Brand: Cadillac Pages: 20

Brand: Pyle Pages: 8

Brand: Mobridge Pages: 20

Brand: Butts of Bawtry Pages: 2

LineCast Auto FM

Brand: Belkin Pages: 15

Brand: Rover Pages: 285

Brand: Xpresskit Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands