RAM Ram 2012 Page 74 Owner'S Manual Download | Manualshive

Page: 74 / 173

background image

To exit ERS mode, simply press and hold the ERS (+)
switch until “D” is once again displayed in the shift lever
position indicator in the instrument cluster.

WARNING!

Do not downshift for additional engine braking on a
slippery surface. The drive wheels could lose their
grip and the vehicle could skid, causing an accident
or personal injury.

Screen Display

1

2

3

4

5

6

D

Actual Gear(s)
Allowed

1

1-2

1-3

1-4

1-5

1-6

1-6

NOTE:

To select the proper gear position for maximum

deceleration (engine braking), simply press and hold the
ERS (-) switch down. The transmission will shift to the
range from which the vehicle can best be slowed down.

Overdrive Operation

The automatic transmission includes an electronically
controlled Overdrive (fifth and sixth gears). The trans-
mission will automatically shift into the Overdrive gear if
the following conditions are present:

Column Shift Lever

72

STARTING AND OPERATING

«
...
72
73
74
75
76
...
»

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments

Related manuals for Ram 2012

Green Motion DC 22

Brand: Eaton Pages: 65

Cherokee 16 1982

Brand: Jeep Pages: 1311

Brand: Calix Pages: 5

Brand: Daewoo Pages: 68

Brand: Hyundai Pages: 437

Brand: Gator Pages: 8

Brand: Hummer Pages: 502

Brand: Hyundai Pages: 19

Brand: Yakima Pages: 13

Brand: Ford Pages: 51

Brand: Yakima Pages: 10

Brand: Chevrolet Pages: 357

Follow me RAPID INTRACKER

Brand: Thule Pages: 8

Camry Hybrid 2012

Brand: Toyota Pages: 62

Brand: walser Pages: 8

Brand: Honda Pages: 76

Brand: Peiying Pages: 28

Brand: Myria Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands