RAM Ram 2012 Page 131 Owner'S Manual Download | Manualshive

Page: 131 / 173

background image

or suspected. Proper maintenance of the entire vehicle
will help the effectiveness of the noise control systems.

Exhaust System

Inspect the entire exhaust system for leaks and damaged
parts. Devices such as hangers, clamps, and U-bolts
should be tight and in good condition. Damaged compo-
nents, burned or blown out mufflers, burned or rusted
out exhaust pipes should be replaced according to the
procedures and specifications outlined in the appropriate
service manual.

Air Cleaner Assembly

Inspect air cleaner housing for proper assembly and fit.
Make certain that the air cleaner is properly positioned
and that the cover is tight. Check all hoses leading to the
air cleaner for tightness. The air filter element must also
be clean and serviced according to the instructions out-
lined in the Maintenance Schedule section of this manual.

Tampering With Noise Control System Prohibited

Federal law prohibits the following acts or the causing
thereof: (1) the removal or rendering inoperative by any
person, other than for purposes of maintenance, repair, or
replacement, of any device or element of design incorpo-
rated into any new vehicle for the purpose of noise
control prior to its sale or delivery to the ultimate
purchaser or while it is in use, or (2) the use of the vehicle
after such device or element of design has been removed
or rendered inoperative by any person.

Among those acts presumed to constitute tampering are
the acts listed below.

•

AIR CLEANER

− Removal of the air cleaner.

− Removal of the air cleaner filter element from the air

cleaner housing.

− Removal of the air ducting.

6

MAINTAINING YOUR VEHICLE

129

«
...
129
130
131
132
133
...
»

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments

Related manuals for Ram 2012

Brand: RAM Commercial Pages: 12

Brand: UMBRA RIMORCHI Pages: 18

Brand: Yakima Pages: 8

Brand: IAG Pages: 3

Brand: Kuda-Phonebase Pages: 3

Brand: Ford Pages: 2

Brand: Honda Pages: 208

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

2 Bike Carrier 977

Brand: Thule Pages: 6

Brand: XTC Pages: 4

Brand: Thule Pages: 8

Evo All THAR-FOR3

Brand: Fortin Pages: 7

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

Brand: Broadfeet Pages: 2

Brand: Prorack Pages: 14

Brand: ORA Pages: 7

Brand: Toyota Pages: 295

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands