manualshive.com logo in svg

RAM Ram 2012, Owner'S Manual, Page: 52 / 173

Share
Download
RAM Ram 2012 Owner'S Manual Download Page 52

WARNING!

Remember to disconnect the cord before driving.
Damage to the 110–115 Volt electrical cord could
cause electrocution.

NOTE:

The block heater will require 110 Volts AC and

6.5 Amps to activate the heater element.

Block Heater Usage

For ambient temperatures below 0°F (-18°C), engine
block heater usage is recommended.

For ambient temperatures below –20°F (-29°C), engine
block heater usage is required.

DIESEL EXHAUST BRAKE (ENGINE BRAKING) —
IF EQUIPPED

The exhaust brake feature will only function when the
driver turns the exhaust brake switch to the ON position.

Once the switch is in the ON position and the vehicle is
moving faster than 5 mph (8 km/h); the exhaust brake
will automatically operate when the driver removes
pressure from the accelerator pedal. Exhaust braking is
most effective when the engine RPM is higher. The
automatic transmission has been programmed in TOW/

Exhaust Brake Switch

50

STARTING AND OPERATING

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments