RAM Ram 2012 Page 85 Owner'S Manual Download | Manualshive

Page: 85 / 173

background image

Fuel Specifications

The Cummins

威

diesel engine has been developed to take

advantage of the high energy content and generally
lower cost No. 2 Ultra Low Sulfur diesel fuel or No. 2
Ultra Low Sulfur climatized diesel fuels. Experience has
shown that it also operates on No. 1 Ultra Low Sulfur
diesel fuels or other fuels within specification.

NOTE:

•

A maximum blend of 5% biodiesel meeting ASTM
specification D-6751 may be used with your Cum-
mins

威

diesel engine.

•

In addition, commercially available fuel additives are
not necessary for the proper operation of your Cum-
mins

威

diesel engine.

•

No. 1 Ultra Low Sulfur diesel fuel should only be used
where extended arctic conditions (-10°F or -23°C) exist.

ADDING FUEL

CAUTION!

To avoid fuel spillage and overfilling, do not “top
off” the fuel tank after filling.

NOTE:

•

When the fuel nozzle “clicks” or shuts off, the fuel
tank is full.

•

Tighten the fuel filler cap until you hear a “clicking”
sound. This is an indication that the fuel filler cap is
properly tightened.

•

Make sure that the fuel filler cap is tightened each time
the vehicle is refueled.

4

STARTING AND OPERATING

83

«
...
83
84
85
86
87
...
»

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments

Related manuals for Ram 2012

Brand: Metra Electronics Pages: 14

Brand: Ford Pages: 52

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Brand: CITROEN Pages: 2

3-series convertible

Brand: BMW Pages: 98

Brand: Dodge Pages: 24

Brand: Boyo Pages: 9

Truck Training Model

Brand: WABCO Pages: 56

Brand: Westfalia Pages: 10

Brand: ConWys AG Pages: 16

Grand Cherokee SRT 2019

Brand: Jeep Pages: 656

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

Brand: Whispbar Pages: 15

Brand: Volvo Pages: 286

Brand: Gator Pages: 5

Brand: Connects2 Pages: 2

MagicWatch MWE850

Brand: Waeco Pages: 200

Electronic Levelling System

Brand: E&P HYDRAULICS Pages: 6

Brand: Yakima Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands