RAM Ram 2012 Page 26 Owner'S Manual Download | Manualshive

Page: 26 / 173

background image

Although your vehicle will usually be drivable and not
need towing, see your authorized dealer for service as
soon as possible.

CAUTION!

Prolonged driving with the MIL on could cause
damage to the engine control system. It also could
affect fuel economy and drivability.

23. Airbag Warning Light

This light turns on and remains on for six to
eight seconds as a bulb check when the ignition
switch is first turned ON. If the light is not on
during starting, stays on, or turns on while

driving, have the system inspected by an authorized
dealer as soon as possible.

24. Front Fog Light Indicator Light – If Equipped

This indicator will illuminate when the front fog
lights are on.

25. Seat Belt Reminder Light

When the ignition switch is first turned ON, this
light will turn on for five to eight seconds as a bulb
check. During the bulb check, if the driver’s seat

belt is unbuckled, a chime will sound. After the bulb
check or when driving, if the driver’s seat belt remains
unbuckled, the seat belt reminder light will flash or
remain on continuously. Refer to

⬙

Occupant Restraints/

Enhanced Seat Belt Use Reminder System (BeltAlert

威

)

⬙

in

“Things To Know Before Starting Your Vehicle” in the
Owners Manual for further information.

24

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
24
25
26
27
28
...
»

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments

Related manuals for Ram 2012

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 24

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Barker Pages: 2

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

Brand: Dometic GROUP Pages: 20

Brand: BGS technic Pages: 5

Brand: Oldsmobile Pages: 344

Brand: ABL Pages: 66

Brand: Whispbar Pages: 15

Brand: AA Products Pages: 4

Brand: ULTIMATE SPEED Pages: 21

DELTA DL FIX 209FP

Brand: Menabo Pages: 8

XEBRA ZAPCAR Series

Brand: Zap Pages: 16

Brand: GMC Pages: 430

Parktronic system Volkswagen Golf MK7

Brand: Car-Systems Pages: 10

Brand: Belkin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands