RAM Ram 2012 Page 145 Owner'S Manual Download | Manualshive

Page: 145 / 173

background image

22,500 Miles (36,000 km) or 18 Months Maintenance Service
Schedule

❏

When prompted by the Engine Oil Indicator System, the engine oil and filter must be
changed. If not prompted by the Engine Oil Indicator System within 7,500 miles
(12 000 km) or six months since the last oil and filter change, change the engine oil and
engine oil filter.

❏

Check the Diesel Exhaust Fluid (DEF) tank, refill if necessary (Chassis Cab Only).

❏

Rotate tires.

❏

Inspect drive belt, replace if necessary.

❏

Lubricate front drive shaft fitting (4x4).

❏

Lubricate outer tie rod ends.

❏

Inspect brake linings.

❏

Inspect and adjust parking brake if necessary.

Odometer Reading

Date

Repair Order #

Dealer Code

Signature, Authorized Service Center

7

MAINTENANCE SCHEDULES

143

«
...
143
144
145
146
147
...
»

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments

Related manuals for Ram 2012

Gasoline/Electric DS Golf Car 1996

Brand: Club Car Pages: 48

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

Brand: Xblitz Pages: 30

Brand: Scion Pages: 24

Brand: Ecco Pages: 24

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: Motoalliance Pages: 5

Brand: Jaeger Pages: 11

Brand: Tesla Pages: 274

Brand: Toyota Pages: 497

Brand: Subaru Pages: 16

Brand: Van Guard Pages: 3

Brand: Ford Pages: 312

Brand: Jeep Pages: 223

Brand: Comtronics Pages: 18

Brand: Guardsman Pages: 3

Brand: Metra Electronics Pages: 8

Brand: AUSTAR Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands