Raisecom RC3000-15 Page 82 Hardware Description Download

Page: 82 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

7 PDH cards

Raisecom Proprietary and Confidential

Table 7-4

PIN definitions of the RJ45 connector

PIN

Name

Description

OUT+

Tx positive pin for the balanced E1 interface

OUT-

Tx negative pin for the balanced E1 interface

IN+

Rx positive pin for the balanced E1 interface

IN-

Rx negative pin for the balanced E1 interface

7.1.5 LEDs

Table 7-5 lists LEDs on the 8E1 card.

Table 7-5

LEDs on the 8E1 card

LED

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Blinking green: the system is working properly.



Off: the system is working improperly.

LAL1–8

Red/

Yellow

Local fault LED



Red: LOS alarms are generated on the local device.



Blinking red: AIS alarms are generated on the uplink of the local
device.



Yellow: LOF alarms generated on the local device.



Blinking yellow: CRC alarms are generated on the local device.

RAL1–8

Red/

Yellow

Remote fault LED



Red: LOS alarms are generated on the peer device.



Blinking red: AIS alarms are generated on the uplink of the peer
device.



Yellow: LOF alarms generated on the peer device.



Blinking yellow: CRC alarms are generated on the peer device.

7.1.6 Internal jumper

Table 7-6 lists jumpers used by the 8E1 card.

Table 7-6

Jumpers used by the 8E1 card

Jumper

Function

J4, J8, J14

Connected to the USB (J5) inside the 8E1 card. When J4, J8, and J14 are
short-circuited, the 8E1 card enters BOOTROM downloading, through
which you can upgrade the BOOTROM.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands