Raisecom RC3000-15 Page 198 Hardware Description Download

Page: 198 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

11 Multi-service card

Raisecom Proprietary and Confidential

173

–

BIT

No.

Description

Function description

OFF (default)

interfaces

3–5

Configure the default
gains (providing four
common gains)

Configuring
gain (A-
D/D-A)

SW1.3 SW1.4 SW1.5

0/0

OFF

0/-3.5

OFF

+14/+4

OFF

+16/+7

OFF

Configuring
data
interfaces

Configure V24
interface mode.

Synchronous mode
(V.24)

Asynchronous
mode (RS232)

Configure RS485
interface mode.

Full duplex (RS422)

Half duplex
(RS485)

Configure bandwidth.

64 kbit/s

128 kbit/s

11.1.8 Specifications

Table 11-13 lists parameters of the 16MULTI card.

Table 11-13

Parameters of the 16MULTI card

Parameter

Description

Dimensions

25 mm (Width) × 225 mm (Depth) × 240 mm (Height)

Weight

0.5 kg

11.1.9 Cables

Table 11-14 lists cables used by the 16MULTI card.

Table 11-14

Cables used by the 16MULTI card

Card

Recommended cable

Description

16MULTI

CBL-MUL-HDB26M/NC

HDB26 male interface to suspended
multifunction cable

CBL-MUL-HDB26M(40)/NC

(Oblique connector) HDB26 male
interface to suspended multifunction
cable

CBL-EM-HDB26M/NC

HDB26 male interface to suspended
E&M cable

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands