Raisecom RC3000-15 Page 37 Hardware Description Download

Page: 37 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

3 Power supply cards

Raisecom Proprietary and Confidential

3.2 SUB-PWRII-AC

3.2.1 Functions and appearance

Panel

Function

The SUB-PWRII-AC card is a 600 W unintelligent power supply
card. It provides the following functions:



Support full-range voltage input.



Support short-circuit protection.



Support input overcurrent protection, output overcurrent
protection, input undervoltage protection, and output
overvoltage protection.



Support hybrid AC/DC power.



Support hybrid intelligent and unintelligent power.



Support over temperature protection.



Support 1+1 hot backup.



Support hot swapping.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands