Raisecom RC3000-15 Hardware Description Download

Page: 114 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

8 Voice cards

Raisecom Proprietary and Confidential

8.4.2 Version

Card

Version

RC3000-15-10E&M

8.4.3 Slots

Chassis version

Slot

E.30

1–6 and 9–13

8.4.4 Interfaces

Interface type

Table 8-25 lists interfaces on the 10E&M card.

Table 8-25

Interfaces on the 10E&M card

Name

Type

Description

1–10

RJ45

Each interface accesses 1 way of E&M voice
service.

Interface parameter

Table 8-26 lists parameters of the interface on the 10E&M card.

Table 8-26

Parameters of the interface on the 10E&M card

Parameter

Description

Coding scheme

A-law

Bit rate

64 kbit/s

Audio port impedance

2000 kΩ during on-hook

600+200//0.1 Ω during off-hook

Effective transmission
bandwidth

300–3400 Hz/600 Ω

Gain frequency features

The Rx (A/D) gain ranges from -3 to 27 dB. The default
value is controlled by an internal jumper. Its step is 0.1 dB.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands