Raisecom RC3000-15 Hardware Description Download

Page: 160 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

10 Data cards

Raisecom Proprietary and Confidential

135

10.1.5 LEDs

Table 10-3 lists LEDs on the 8ETHP card.

Table 10-3

LEDs on the 8ETHP card

LED

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Blinking green: the system is working properly.



Off: the system is working improperly.

100M (1–8)

Green

Electrical interface rate LED



Green: the electrical interface is working at 100 Mbit/s.



Off: the electrical interface is working at 10 Mbit/s.

LNK/ACT
(1–8)

Green

Ethernet link interface LED



Green: Ethernet link interfaces are connected properly.



Blinking green: Ethernet link interfaces are receiving or
sending data.



Off: Ethernet link interfaces are disconnected or are
improperly connected.

10.1.6 Internal jumper

Table 10-4 lists the internal jumper used by the 8ETHP card.

Table 10-4

Internal jumper used by the 8ETHP card

Jumper

Function

Status

Description

Configure
the mode for
downloadin
g the MCU
program.

Short-circuited

Enter ISP mode. In this mode, the RC3000-
15 is waiting to be upgraded. You can
upgrade MCU program through the serial
interface on the backplane.

Disconnected

Enter normal working mode.

After upgrade, J9 must be disconnected; otherwise, the RC3000-15 will malfunction.

10.1.7 Specifications

Table 10-5 lists parameters of the 8ETHP card.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands