Professional auto-ranging digital
multimeter
model no:
mm102
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
1.1.
Personal PreCautions
9
When using this meter, please observe all normal safety rules concerning:
Protection against the dangers of electric current.
Protection of the meter against misuse.
9
Full compliance with safety standards can only be guaranteed if used with the test leads supplied. Failure to do so will invalidate the
warranty.
8
do not
use leads if damaged or if the wire is bared in any way.
1.2.
general safety instruCtions
9
Familiarise yourself with the applications, limitations and hazards of the meter.
If in any doubt consult a qualified electrician.
9
When the meter is linked to a measurement circuit,
do not
touch unused meter terminals.
9
When the scale of the value to be measured is unknown set the selector to the highest range available.
9
Before rotating the range selector to change functions, disconnect test leads from the circuit under test.
Warning!
never perform resistance measurements on live circuits.
9
Always be careful when working with multimeter. Keep your fingers behind the probe guards while measuring.
9
When not in use, store the meter carefully in a safe, dry, childproof location. Storage temperature range -10°C to 50°C
8
do not
apply voltage or current to the meter that exceeds the specified maximum.
9
The user shall ensure that test probes are correctly selected in order to prevent danger. Probes shall be selected to ensure that
adequate barriers guard against inadvertent hand contact with live conductors under test and that probes have minimal exposed
probe tips. Where there is a risk of the probe tip short circuiting with other live conductors under test, it is recommended that the
exposed tip length shall not exceed 4mm.
2. introduCtion
lightweight, auto-ranging digital multimeter with double moulded plastic housing and a 2000 counts lCd display. Features forward facing work
light, data hold and non-contact AC voltage detection. Conforms to en 61010-1 CATIII 1000V / CAT IV 600V safety standard.
measures: AC and dC Voltage, AC and dC Current, Resistance, diode Test, Continuity Test.
3. sPeCifiCation
model no ...............................................................................................................................................mm102
AC Voltage (Accuracy) ...............................................................................2V, 20V (±1%), 200V, 600V (±2.3%)
dC Voltage (Accuracy) ...............................................................200mV (±0.5%), 2V, 20V, 200V, 600V (±1.2%)
AC Current (Accuracy) ........................................................................200µA, 2000µA, 20mA, 200mA (±2.5%)
dC Current (Accuracy)........................................................................... 200µA, 2000µA, 20mA, 200mA (±2%)
Resistance (Accuracy)
.........................200Ω.(±0.8%),.2KΩ,.20KΩ,.200KΩ.(±1.2%),.2MΩ.(±5%),.20MΩ.(±10%)
Capacitance (Accuracy).................................................................................................................................no
Frequency (Accuracy). ...................................................................................................................................no
duty Cycle ......................................................................................................................................................no
Continuity Audible ................................................ ........................................................................................Yes
diode Test ..................................................................................................................................... ...............Yes
Transistor Test ...............................................................................................................................................no
Hi- Impact Case .............................................................................................................................................no
digits x Height.....................................................................................................................................4 x 14mm
low Battery Indicator ....................................................................................................................................Yes
Batteries (supplied) ......................................................................................................................... 2 AAAx1.5V
Size (l x W x d) ......................................................................................................................105 x 57 x 34mm
Weight ........................................................................................................................................................160g
Conformity ........................................................................................................................................en61010-1
non-Contact Voltage detection VAC ......................................................................................... .....100V - 600V
m
M102.|.Issue.2.(F).28/03/18
Original Language Version
© Jack Sealey limited
Refer to
instructions
electrical
shock
hazard
