Raisecom ISCOM2600G-HI (A) Series Configuration Manual Download Page 306 | Manualshive

Page: 306 / 581

background image

Raisecom
ISCOM2600G-HI (A) Series Configuration Guide

6 DHCP

Raisecom Proprietary and Confidential

Copyright © Raisecom Technology Co., Ltd.

275

Step

Command

Description

3

Raisecom(config)#interface

interface-type

interface-number

Raisecom(config-gigaethernet1/1/port)#ipv6
dhcp option

number

{

ascii

ascii-string

|

hex

hex-string

|

ipv6-address

ipv6-address

}

(Optional) create user-
defined Option
information over IPv6
on the interface.

6.4.8 Checking configurations

Use the following commands to check configuration results.

No.

Command

Description

1

Raisecom#show ip dhcp
information option

Show configurations of DHCP Option fields.

2

Raisecom#show ip dhcp
option port vlan
description

Show the interface or VLAN description to
be padded into Option 82 fields.

6.5 DHCP Server

6.5.1 Introduction

Dynamic Host Configuration Protocol (DHCP) refers to assigning IP address configurations
dynamically for users on the TCP/IP network. It is based on BOOTP (Bootstrap Protocol)
protocol, and automatically adds the specified available network address, network address re-
use, and other extended configuration options over BOOTP protocol.

With the enlargement of network scale and development of network complexity, the number
of PCs on a network usually exceeds the maximum number of distributable IP addresses.
Meanwhile, the widely use of laptops and wireless networks lead to frequent change of PC
positions and also related IP addresses must be updated frequently. As a result, network
configurations become more and more complex. DHCP is developed to solve these problems.

DHCP adopts client/server communication mode. A client applies configuration to the server
(including IP address, subnet mask, and default gateway), and the server replies with an IP
address for the client and other related configurations to implement dynamic configurations of
IP address.

In DHCP Client/Server communication mode, a specific host is configured to assign IP
addresses, and send network configurations to related hosts. The host is called the DHCP
server.

DHCP application

Under normal circumstances, use the DHCP server to assign IP addresses in following
situations:



The network scale is large. It requires much workload for manual configurations, and is
difficult to manage the entire network intensively.

«
...
304
305
306
307
308
...
»

Summary of Contents for ISCOM2600G-HI (A) Series






































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ISCOM2600G-HI (A) Series

Brand: Ultra Pages: 20

Brand: P-Link Computer Pages: 92

Edison Cooper Power Series

Brand: Eaton Pages: 12

FL SWITCH SFN 16TX

Brand: Phoenix Contact Pages: 6

Brand: SUCO Pages: 2

SEHI SEHI100TX-

Brand: Cabletron Systems Pages: 75

Brand: NA-DE Pages: 4

Brand: X-keys Pages: 4

Brand: senva Pages: 2

Brand: Alloy Pages: 13

Brand: MicroNet Pages: 74

Brand: Kinesis Pages: 12

Brand: Mengual Pages: 2

Brand: Veris Industries Pages: 2

Brand: CYP Pages: 64

Brand: United Integrated Services Pages: 6

Brand: C&H Technologies Pages: 1

FlexFabric 12900

Brand: HPE Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands