Radiopost TS401 User Manual Download Page 62

Page: 62 / 70

Move to MST using the

DOWN

twice. Press the

SET

and select the

slave channel using the

LEFT

and the

RIGHT

. Press the

SET

again

to save the slave channel.

Move to the Left (Or FWRD) by pressing the

three times. Press

the

SET

and use the

LEFT

and the

RIGHT

to modify the mix rate.

Press the

SET

again to save the rate. Mix rate is the range

between -10 and 120. The default is 50.

Move to the Right (Or BRAK) by pressing the

DOWN

three times.

Press the

SET

and use the

LEFT

and the

RIGHT

to modify the mix

rate. Press the

SET

again to save the rate. Mix rate is the range

between -10 and 120. The default is 50.

Move to OFST by pressing the

and the

RIGHT

. Press the

SET

and use the

LEFT

and the

RIGHT

to modify the offset. Press the

SET

again to save the offset. Offset is the range between -100 and

100. The default is 0.
Move to MXMD using the

DOWN

. Press the

SET

and use the

LEFT

and the

RIGHT

to select OFF and MIX. Press the

SET

again to save

the selection. If MIX is selected, mixing is applied after master

channel‟s function is applied. If OFF is selected, mixing is applied

before master channel‟s function is applied.

Move to MXMD using the

DOWN

. Press the

SET

and use the

LEFT

and the

RIGHT

to select OFF and ON. Press the

SET

again to save

the selection. If ON is selected, mixing is applied after master

channel‟s trim is applied. If OFF is selected, mixing is applied

before master channel‟s trim is applied.

Summary of Contents for TS401







































































Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands

Radiopost TS401, User Manual

Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands