Radiopost TS401 User Manual Download Page 48

Page: 48 / 70



UP Timer

The timer‟s range is 0 to 99.9999 minutes.

Alarms can be set in 1 minute increments.

Pre-alarms can be set in 1 second increments.

When the timer reaches the set alarm time, alarm sound is made.

When a pre-alarm is set, the warning sound beeps for the set pre-alarm

period before the timer reaches the set alarm time.

When the timer reaches the set alarm time, alarm sound is made.

If the user does not stop the timer even after alarm sound has been

made, the warning sound beeps every one minute.

Move to TYPE using the

DOWN

and press the

SET

. Then, select

UP and press the

SET

Move to ALRM using the

DOWN

and press the

SET

. Set the alarm

time and press the

SET

The alarms can be set in 1 minute increments up to 99 minutes.

(e.g. OFF/1min./2min.~99min.)

Move to PRAL using the

DOWN

and press the

SET

. Set the pre-

alarm and press the

SET

The pre-alarms can be set in 1 second increments up to 99 seconds.

(e.g. OFF/1sec./2sec.~99sec.)

■

How to Set the Timer



FUEL DOWN Timer

The time on the timer is decreased from the set alarm time to “0”.

When the timer reaches “0”, the alarm sound is made.

If the user does not stop the timer, the time continues to decrease.

Summary of Contents for TS401







































































Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands

Radiopost TS401, User Manual

Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands