Radiopost TS401 User Manual Download Page 60

Page: 60 / 70

5.18.7 AUX CH Position

Move to the channel which is desired to change the position. Press

the

SET

and change the position value. The value is the percentage

ranging from -100% to 100%, and it can be controlled with

resolution of 0.1%. Press the

LEFT

to decrease the value by 0.1%.

Press the

RIGHT

to increase the value by 0.1%. Press the

DOWN

decrease the value by 1%. Press the “

” to increase the value by

1%. The default is 0%.

■

How to Set

5.18.8 Boat Mode

Boat does not include move backward, thus the whole range of -

100%~+100% can be used as forward movement. If TRG-BRK is set to

Cut Off, all range of the receiver output will be used for acceleration.

Tilt Mixing is used to mix the 1

channel (typically, rudder channel)

and 3

channel.

It is used to change the position of auxiliary channels. (the 3

channel and the 4

channel.) Auxiliary channels can be assigned to

the Dial Switches or Trim switches for instant change.

Summary of Contents for TS401







































































Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands

Radiopost TS401, User Manual

Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands