Radiopost TS401 User Manual Download Page 61

Page: 61 / 70

■

How to Set

Press the

SET

when placed in TRG-BRK, and use the

RIGHT

modify it to Cut Off. Press the

SET

again to save it.

5.18.9 Prog Mix

It is used to mix one channel to the other channel. Two mixing is

available and each can be programmable independently and work

independently.

Move to Mode using the

DOWN

. Press the

SET

and use the

RIGHT

to change it to On. Press the

SET

again to activate the function.

Move to CH1->3 using the

DOWN

. Use the

LEFT

and the

RIGHT

modify the rate. Press the

SET

again to save the modified value.

The value is in the range from -100% to 100%.

The default is 100%.

Move to Ch 3



1 using the

DOWN

. Use the

LEFT

and the

RIGHT

to modify the rate. Press the

SET

again to save the modified value.

The value is in the range from -100% to 100%. The default is 100%.

■

How to Set

Press the

SET

when being placed in the Mode, and use the

RIGHT

to select ACT. Press the

SET

again to save the activation.

Move to MST by pressing the

DOWN

twice. Press the

SET

and

select the master channel using the

LEFT

and the

RIGHT

. Press the

SET

again to save the master channel.

Summary of Contents for TS401







































































Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands

Radiopost TS401, User Manual

Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands