Radiopost TS401 User Manual Download Page 35

Page: 35 / 70

5.9 Selection of Switch

5.9.1 Push Switch

There are 3 push switches on the transmitter:

PS1

PS2

and

PS3

. The

functions shown in the below table can be assigned to each push

switch. The default setting of push switches is OFF.

The table shows the functions that can be assigned to the push

switches.

Item

Functions

OFF

Not Assigned

PRESET

Enables Auto Start

NT-BRAKE

Enables Neutral Brake

ABS.CH2

Enables ABS over Channel 2

ABS.CH3/4

Enables ABS over Channel 3/4

IDLE-UP

Enables Idleup

PROG MIX1

Enables Program Mix 1

PROG MIX2

Enables Program Mix 2

CH3

Channel 3 Value

CH4

Channel 4 Value

LAP START

Starts Timer

LAP RESET

Resets Timer

■

How to Set

In order to assign a function to PS1, press the

SET

and move to the

preferred function using the

LEFT

and

RIGHT

and press the

SET

again.

Move to the right side of screen by pressing the

RIGHT

” to set the

motion types between Normal and Alternative.

How to assign functions to PS2 and PS3 is same as that to PS1.

But note that PS3 has a Normal motion and Reverse motion.

Summary of Contents for TS401







































































Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands

Radiopost TS401, User Manual

Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands