Radiopost TS401 User Manual Download Page 4

Page: 4 / 70

▣ Precautions for the Transmitter

▣ Precautions for the Receiver

distributors or dealer in your country, please immediately contact the

seller to determine if such export regulations have been met. Use of this

product with other than models may be restricted by the export and

trade control regulations and an application for export approval must be

submitted.

▶ (Modifications, Adjustment and Replacement of Parts) Radiopost is not

responsible for the unauthorized modification, adjustment and

replacement of parts on this product. Any such changes may void any

or all warranties associated with this product.

▶ To start, first switch on the transmitter and secondly, the receiver.

After using the RC Model, please switch off the receiver first and then

the transmitter. Reversing the order of powering on and off may cause

critical damages to the devices or persons.

▶ Please check if the batteries for transmitter and receiver are fully charged

before starting.

▶ The antenna for Radiopost‟s transmitter TS450 2.4GHz is built-in the

product (Internal). The antenna in located underneath the front top

section, above the power switch of the transmitter. Be careful not to

cover this part of transmitter, as it may cause weak signal output if

covered.

▶ The receiver antenna is made of coaxial cable that consists of a covered

part and naked wire part. The naked wire is used to receive the radio

wave. Be careful not to bend the naked part of the wire, as it also may

weaken the signal quality of the receiver.

▶ An antenna cable is very delicate. Please handle it with care.

▶ Do not forcibly pull the antenna cable.

▶ Do not cut or link the antenna cable with other wires.

Summary of Contents for TS401







































































Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands

Radiopost TS401, User Manual

Search results

Summary of Contents for TS401

Reviews:

Related manuals for TS401

Brands by name

Popular brands