TO 31R2-2TRC199-1
Change 1
2-9/(2-10 blank)
2-10.2
Lithium Battery Installation.
(Optional)
(This procedure is also applicable to the Type BB-590/U NiCad batteries.) The battery enclosure has
connectors for four type BA-5590/U Lithium batteries.
The connectors are mounted in the bottom of the enclosure. To
install the batteries, first open the battery enclosure. Taking each battery, in turn, turn the battery so that the connector
is facing down, align the connector on the battery with the connector in the bottom of the enclosure, and push down on
the battery until seated.
To power the tactical repeater from the installed batteries, set the power supply POWER switch to DC, and the DC SEL
switch to INT.
The repeater is capable of full operation with either three or four batteries installed.
2-10.3
Ground Rod Installation.
The ground rod assembly consists of a 3 foot long ground rod and an attached 10 foot grounding strap. The grounding
strap ends in a spade lug that is connected to a ground screw on the tactical repeater assembly frame next to the power
supply assembly.
To install, place the tactical repeater in its selected operating location. Locate the ground lug on the frame and select a
spot for the ground rod within a 10 foot arc of the ground screw. Drive the ground rod into the ground with a sledge
hammer until the grounding strap clamp is level with the ground. Remove the wing nut and washer from the ground
screw, place the spade lug over the screw, and reattach the washer and wing nut.
2-10.4
External Power Supply.
To connect the tactical repeater to an external power supply, select the appropriate power supply cable to match the
external source (110/220 VAC, 240 VAC, or 10-32 VDC). Connect the power supply cable to the POWER IN connector
on the power supply and connect to the power source. Set the power supply POWER switch and DC SEL switch as
indicated in Table 2-3.
Table 2-3. External Power Supply Switch Settings
POWER SOURCE
POWER
DC SEL
110/220 VAC
AC
N/A
240 VAC
AC
N/A
10-32 VDC
DC
EXT
2-10.5
Diplexer Installation.
Refer to paragraph 6-5.1.6.
2-10.6
Receiver-Transmitter Transceiver Module Installation.
Refer to TO 31R2-2PRC139-1.
Summary of Contents for AN/TRC-199
