TO 31R2-2TRC199-1
3-2
3-3.2
Alignment and Adjustment.
The tactical repeater is aligned and adjusted for normal operation at the factory/depot. No other alignments or
adjustments are authorized or required. The diplexer will require retuning as described in paragraph 4-3 whenever the
transmit or receive frequencies are changed.
3-3.3
Post-Installation Checkout Procedures.
After completion of installation, perform the following checkout procedures.
3-3.3.1
Power-Up Check.
Perform the power-up check as follows:
a.
Ensure the receive receiver-transmitter is programmed with the proper type squelch settings to receive
the desired modulation format (carrier squelch or CTCSS tones).
b.
Place the tactical repeater MODE SELECT switch (6, Figure 4-1) in the OP2WATT or OP10WATT
position.
c.
Place the power supply AC/DC POWER switch (1, Figure 4-2) in either AC or DC position, depending
on source of power. If DC is selected, the DC SEL switch must be set for internal (INT) or external
(EXT) power source, as appropriate.
d.
Ensure that the green POWER LED is illuminated when the DISPLAY switch is ON. This indicates
that the unit is receiving power from the power converter.
3-3.3.2
Operational Check.
Perform the operational checkout included in paragraph 6-2 to verify that the major components of the tactical repeater
are properly functioning.
3-3.3.3
Equipment Shutdown.
Shut down the tactical repeater as follows:
a.
Set the power supply POWER switch to OFF.
b.
Ensure that the POWER LED is not illuminated.
Section II. PREPARATION FOR RESHIPMENT
3-4
PREPARING UNIT FOR RESHIPMENT.
Prepare the tactical repeater for reshipment as follows:
a.
Disconnect all external accessories, antennas, and cables.
b.
Remove the receiver-transmitters prior to shipment.
c.
Remove batteries (if installed).
3-5
PACKING.
Pack the tactical repeater in the recommended packages illustrated in Figure 2-1. Use original packing materials if
available.
3-6
HANDLING AND STORAGE.
Place electronic assemblies in individual containers. This will prevent damage during handling and storage. If a common
container is used, use suitable barrier material between electronic assemblies. Sufficient packing must be used to prevent
shifting of electronic assemblies within the container. Package the equipment in accordance with MIL-STD-2073-1A/2B.
Marking for reshipment and storage shall be in accordance with MIL-STD-129J.
Summary of Contents for AN/TRC-199
