![background image](http://html1.mh-extra.com/html/directechs/pkuch2gx/pkuch2gx_installation-manual_2506732001.webp)
R
E
M
O
T
E
S
Y
S
T
E
M
Red
Orange
Green
Blue
Violet (+)
Black
Violet/White
Brown (-)
Pink (+)
(+) 12 VOLT CONSTANT
Pink/White (-)
N/C
N/C
DATA OUTPUT TO VIOLET/BROWN (2ND START WIRE)
+12 VOLT STARTER INPUT TO REMOTE STARTER
DISARM INPUT
IGNITION INPUT
N/C
CHASSIS GROUND
COIL
NOTE:
3 OR 5 TURNS OF LOOP IS REQUIRED
LOCATE THE COIL AROUND THE IGNITION KEY
YOU CAN PROGRAM THE TRANSPONDER ONLY ONCE.
Ground when running (remote start installations only)
PKU MODULE PROGRAMMING MODE
You will need 2 valid keys. Proceed as follows:
1-Insert first key and turn to the
IGN “ON”
position: “THEFT” light will turn ON, then go
“OFF”.
Remove the first key.
2
-
Within 5 seconds, insert second key: turn and hold in
IGN “ON”
position. After approx. 10 seconds, the door chime
will sound**
once
to indicate vehicle is in programming mode.
YOU NOW HAVE 60 SECONDS TO PROCEED WITH THE NEXT STEP.
3
-
For the next 2 steps position & hold the PKU module (screw side) towards the front of the ignition barrel (key cylinder).
(Coil Loop is NOT USED during PK programming)
4
-
Using a jumper wire, power up vehicle ignition, without starting vehicle, for approx. 10 secs. until the “THEFT” light
comes
“ON”
solid. “THEFT” light will then flash and return back to solid to indicate the PKU module is now
programmed successfully.
IMPORTANT NOTE:
Once the PK (Transponder Bypass) portion has been programmed to a vehicle, it cannot be used on any other
Chrysler vehicle. (This a Chrysler Sentry Key feature from factory.)
**As a reference:
door should be left open during programming.
- No wiring harnesses should be connected while programming Transponder Bypass.
- Do not install bypass module on a metal surface.
- Do not install resistor’s they are internal.
TECH NOTE:
Ground When Running (-) (remote Start Installations Only)
N/C
N/C
Data Ouput To Violet/brown 2nd Start Wire (Wire Located In The Steering Column)
12 Volt Starter Input To Remote Starter (Wire In Parallel With Vehicle Start Wire)
Disarm Input (Connect To The Disarm Output From Remote System)
Ignition Input To Vehicle (Connect To Main Ignition Of Vehicle)
N/C
(+)12 Volt Constant
Chassis Ground
WIRE FUNCTIONS
Brown
Green
Blue
Violet/White
Violet
Pink/White
Pink
Orange
Red
Black
1
0
P
IN
H
A
R
N
E
S
S
ST
1 Generation
Connector
ND
2 Generation
Connector
1
0
P
IN
H
A
R
N
E
S
S
Description:
Chrysler 1st & 2nd Generation Sentry Key Override with 2nd Start Activation Output (
Functions:
No Key Required)
Installation
Manual (1\3 Pages)
PKUCH2GX
Transponder Bypass Kit for 1st & 2nd generation encrypted Chrysler Sentry key immobilizer systems. This transponder
bypass kit will override all Chrysler, Dodge & Jeep vehicles equipped with the 1st & 2nd generation type of Sentry
transponder key. PKUCH2GX designed with MUX (2nd starter & accessory wire) activation output
Bypass Method: RF override through induction using loop antenna.
which initiates the 2nd
Starter & 2nd accessory wire during start up.