background image

Chapter 3  Installing the Library

Connecting the Library to the Host Controller

Quantum|ATL 7100 Series Facilities Planning and Installation Guide

29

Table 5   7100 Series 
SCSI Cabling 
Configuration

The following procedure describes how to connect a 4/100 library 
to the host when using the default two-wire, four-drive 
configuration:

1

Remove power from the library as follows:

a

Press and release the control panel 

STANDBY

 button, and 

verify that System Off-line is displayed in the SDA.

b

At the rear panel, set the 

POWER

 button to the “

0

” (off) 

position.

2

Power down all SCSI devices that will be connected on the 
same bus as the library.

3

Connect the two library-to-host SCSI cables to the host 
adapters.

Library Configuration

Default SCSI Wiring Configuration

2/68

1-Wire

4/68

2-Wire

7/68

4-Wire

2/100

1-Wire

4/100

2-Wire

7/100

4-Wire

Caution:

The library uses differential (diff) SCSI 
connections. If your host adapter is single-ended 
(SE) SCSI, you must use a SE-to-diff converter for 
proper communications.

Summary of Contents for ATL 7100





































































Reviews: