background image

 250-7061C  December 10, 2004

Page 32

R

ATTENTION INSTALLERS:

PLEASE RETURN THESE INSTRUCTIONS TO THE HOME 

OWNER WHEN THE INSTALLATION IS COMPLETE 

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 

4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 

5341794,  5347983,  5429495,  5452708,  5542407,  5601073,  5613487,  5647340,  5688568,  5762062, 

5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 

6170481,  6237588,  6296474,  6374822,  6413079,  6439226,  6484712,  6543698,  6550687,  6601579, 

6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; 

(Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending.

CONTACT INFORMATION

:

Hearth & Home Technologies

1445 North Highway

Colville, WA  99114

Division of HNI INDUSTRIES

www.quadrafire.com

Please contact your Quadra-Fire dealer with any questions or concerns. 

For the number of your nearest Quadra-Fire dealer,

call 1-800-926-4356

•  Do NOT discard this manual.
•  Important operating and maintenance 

instructions included.

•  Read, understand and follow these instruci-

tons for safe installation and operation.

•  Leave this manual with party responsible for 

use and operation.

CAUTION

R

Summary of Contents for 4300 Series

































Reviews: