Page 17
March 27, 2008
4100-I ACT WOOD INSERT
250-7201 Rev D
R
WOOD SELECTION AND STORAGE
B
urn only dry seasoned wood. Dry, well-seasoned wood will not only minimize the chance of creosote formation but will
give you the most effi cient heat output. Even dry wood contains at least 15% moisture by weight and should be burned hot
enough to keep the chimney hot enough to maintain particulate (smoke) burning. Burning unseasoned wood of any variety
defeats the inserts’ effi ciency.
Dead wood lying on the forest fl oor should be considered wet, and requires full seasoning time. Standing wood can be
considered to be about two-thirds seasoned. Wood is dry enough to burn if the ends of the logs have cracks radiating in all
directions from the center. If your wood sizzles in the fi re, even though the surface is dry, it may not be fully cured.
Drying time can be reduced by splitting wood prior to storage. Since the majority of drying occurs through the cut ends
rather than the sides, stack the wood so both ends of each piece are exposed to air. Store wood under cover, such as in a
shed, or covered with a tarp, plastic, tar paper, sheets of scrap plywood, etc.
OVERFIRING
Do not overfi re. Overfi ring can result in crazing, an effect causing a white, non-removable fi lm to be deposited on the
inside of the glass. Using fl ammable liquids or too much wood, or burning trash in the insert, may result in overfi ring. If
the chimney connector or insert glows red, or worse, white, the insert is overfi red. This condition may ignite creosote in
the chimney, possibly causing a house fi re. If any part of the insert starts to glow, you are in an overfi re situation. If you
overfi re, immediately close the insert controls and door, if open, to reduce the air supply to the fi re.
Overfi ring your insert
voids your warranty.
NOTE: The special high temperature fi nish paint applied to the insert will cure as your insert heats. You will notice
an odor and perhaps see some vapor rise from the insert surface, this is normal. We recommend that you open a
window until the odor dissipates and the paint is cured.
OPERATION
Before lighting your fi rst fi re in the insert, make certain that the baffl e is correctly positioned. It should be resting against the
rear support. Also refer to care and cleaning of plated surfaces on
page 19
before lighting your fi rst fi re.
CAUTION: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fl uid, or similar liquids to start
or “freshen up” a fi re in this heater. Keep all such liquids well away from the heater while it is in use.
There are many ways to build a fi re. The basic principle is to light easily-ignitable tinder or paper, which ignites the fast-burn-
ing kindling, which in turn ignites the slow-burning fi rewood. Here is one method that works well:
1.
Place several wads of crushed paper on the fi rebox fl oor.
Heating fl ue with slightly crumpled newspaper before adding
kindling keeps smoke to a minimum.
2.
Lay small dry sticks of kindling on top of the paper.
3.
Open Start-Up Air Control (bottom rod) and Primary Air Control (top rod) fully.
See Figure 19A on page 19.
4.
Ensure that no matches or other combustibles are in the immediate area of the insert, that the room is adequately
ventilated, and the fl ue is unobstructed.
5.
Light the paper in the insert. NEVER light or rekindle insert with kerosene, gasoline, or charcoal lighter fl uid; the results
can be fatal.
6.
Once the kindling is burning quickly, add several full-length logs three inches (76mm) or four inches (102mm) in diameter.
Be careful not to smother the fi re. Stack the pieces of wood carefully. They should be near enough to keep each other
hot, but far enough away from each other to allow adequate air fl ow between them.
7.
When ready to reload the insert, add more logs. Large logs burn slowly, holding a fi re longer. Small logs burn fast and
hot, giving quick heat.
8.
Adjust the Start-Up Air Control and Primary Air Control, maintaining fl ames above the fuel. The more you close down
the Primary Control, the lower and slower the fi re will burn. The more you open the Primary Control the more heat will
be produced. The Start-Up Air Control (bottom rod) is only used for the fi rst 5 to 15 minutes.
As long as there are hot coals, repeating steps 7 and 8 will maintain a continuous fi re.
BUILDING A FIRE
NOTE: Remove all labels from glass front prior to lighting the fi rst fi re.
