background image

DO NOT DISCARD THIS MANUAL

NOTICE

• 

Important operating 
a n d   m a i n t e n a n c e 
instructions included.

• 

Leave this manual with 
party responsible for 
use and operation.

• 

Read, understand and 
follow these instructions 
for safe installation and 
operation.

DO N

O

T

DIS

CA

RD

WARNING

If the information in these 
instructions is not followed 
exactly, a fi re may result causing 
property damage, personal injury, 
or death.

 

•  Do not store or use gasoline or other 

fl ammable vapors and liquids in the 
vicinity of this or any other appliance.

•  Do not overfi re - If heater or chimney 

connector glows, you are overfi ring. 
Overfi ring will void your warranty.

•  Comply with all minimum clearances to 

combustibles as specifi ed.  Failure to 
comply may cause house fi re.

www.quadrafi re.com  

4100- I ACT WOOD INSERT

Advanced Combustion Technology (ACT)

O-T 

O-T L

Tested and 

Listed by

Beaverton

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

250-7201D     March 27, 2008

1445 North Highway
Colville, WA 99114-2008

R

Installation and service of this appliance should 
be performed by qualifi ed personnel.  Hearth & 
Home Technologies recommends NFI certifi ed 
professionals, or technicians supervised by an 
NFI certifi ed professional.

Fire Risk.

WARNING

For use with solid wood fuel only.
Other fuels may overfi re and generate 
poisonous gases (i.e. carbon monoxide).

HOT SURFACES!

G L A S S   A N D   O T H E R 
S U R FA C E S   A R E   H O T 
DURING OPERATION AND 
COOL DOWN.

WARNING

Hot glass will cause burns.

•  Do not touch glass until it is cooled 
•   NEVER allow children to touch glass
• Keep 

children 

away

•  CAREFULLY SUPERVISE children in the same room 

as  appliance

•   Alert children and adults to hazards of high 

temperatures

High temperatures may ignite clothing or other 

fl ammable materials.

•  Keep clothing, furniture, draperies and other 

combustibles away. 

Models:

4100I-GD-B
4100I-NL-B

Summary of Contents for 4100I-GD-B





























Reviews: