manualshive.com logo in svg

Qlogic QLE2740L-DEL, User Manual

Share
Download
Qlogic QLE2740L-DEL User Manual Download Page 118

A–Troubleshooting
Troubleshooting with a Diagnostic Port (D_Port)

103

BK3254601-00  C

When a switch port is enabled as a D_Port, the QLogic 2700 Series Adapter 
automatically runs the basic diagnostic test at both ends of the link. The Brocade 
switch then runs the following additional tests:

Electric loopback test

Optical loopback test

QLogic recommends running D_Port tests on multipath configured boot from 
SAN/fabric-assigned boot LUN. Running D_Port tests on single path boot from 
SAN/fabric-assigned boot LUN may cause issues with OS stability in true boot 
from SAN environments. 

The following sections describe how to configure and run D_Port mode from the 
Brocade Fibre Channel 16 switch, and how to verify D_Port mode from the 
QConvergeConsole utilities:

Configuring D_Port on a Brocade Fibre Channel 16G or 32G Switch

Checking D_Port Results from a Brocade Fibre Channel 16G or 32G Switch

Verifying D_Port Mode with QConvergeConsole GUI

Verifying D_Port Mode with Interactive QConvergeConsole CLI

Verifying D_Port Mode with Noninteractive QConvergeConsole CLI

Verifying D_Port Mode with QConvergeConsole Plug-ins

Configuring D_Port on a Brocade Fibre Channel 16G or 32G 

Switch

To enable D_Port diagnostic mode:

From the Brocade Fibre Channel 16G or 32G switch, issue the following 
commands:

# 

portdisable <port#>

# 

portcfgdport ––enable

 

<port#>

# 

portenable

 

<port#>

The D_Port test starts automatically.

NOTE

All QLogic-branded 32Gbps SFP+ transceivers support the functionality 
required to run D_Port tests. If you have a supported non-QLogic branded 
transceiver, ensure that it supports the optical wrap (OWrap) and electrical 
wrap (EWrap) capability that is required for D_Port. 

Summary of Contents for QLE2740L-DEL








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands