background image

 

Description 

 

 

 

UM Pallet stacker Prmk10-PS v2.0 EN 

27 

 

The Prmk10-PS can stack virtually any pallet size. With an increase in pallet size, the footprint 
of the Prmk10 also increases. The length and width of the Prmk10 is increased in steps of 
150mm. Adequate safe space between the forks and the pallets must also be taken into 
consideration. Consult Qimarox for information about the correct Prmk10 footprint. 

To ensure pallets are stacked safely, the pallets must be centered in the middle of the 
Prmk10. This can be done by using a pallet stopper and/or pallet center unit. These are not in 
the scope of delivery and must be supplied by the integrator or OEM. 

 

Specifications 

Always comply with the specifications below, in the specification sheet, on the type plate and 
in the electrical drawings. 

If a different product weight or dimension is required, the machine must be adjusted to 
accommodate this. These type of adjustments may only carried out by Qimarox or after written 
permission from Qimarox has been obtained. 

 

Environmental specifications 

Unless otherwise specified in the specification sheet of the machine, the surrounding area of 
the machine must comply with the following specifications: 

Property 

Description 

General 

Inside and normally clean for operation. There must be sufficient 
space around the machine to carry out maintenance and other 
activities on the machine.. 

Relative air 
humidity 

Maximum 80% 

Temperature 

B5°C (41 F) and 40°C (104 F) 

Max. altitude 

1000m above sea level 

 
When the specifications for the surrounding area deviate from the table above, the machine 
must be adjusted to this. Such adjustments shall always be carried out by Qimarox or after 
permission from Qimarox. 
 

 

Pneumatic specifications 

Unless otherwise specified on the type plate and in the specification sheet of the machine, the 
compressed air supply should be between 5 bar and 7 bar in accordance with ISO 
85731:2010 [7:4:4] 

 

Electrical specifications 

Refer to the type plate and specification sheet of the machine for the electrical specifications. 
Refer to the electrical circuit diagrams of the machine. 

 

 

Summary of Contents for Prmk10-PS





































Reviews: