9
•
Check the machine for possible damage:
- Before further use of the machine the safety devices must
be checked carefully for their proper and intended function.
- Check whether movable parts function perfectly and do
not stick or whether parts are damaged. All parts must be
correctly installed and fulfil all conditions to ensure perfect
operation of the machine.
- Damaged safety devices and parts must be properly
repaired or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for use.
- Damaged or illegible safety labels have to be replaced.
•Store unused equipment in a dry, locked place out of the reach
of children.
Shockproof concrete mixers
(Protection Class II)
• Only
start
the machine when the panelling is complete and fully
closed.
•
Protection Class II
applies only if original insulating material is
used for repairs and insulation clearances are not altered.
Electrical safety
Danger to life and limb if not observed!
•
Connecting attachments
must be designed in conformance
with IEC 60245-4:1980 (DIN 57 282) and marked H 07 RN-F, or
comparable models. Cross section of wires at least 3 x 1.5 mm²
up to a maximum length of 25 m. Wire cross-section at least 2.5
mm² for lengths of more than 25 m.
• Use only
connecting attachments
with a rubber plug device
for severe requirements
that is protected against spraying
water.
• Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the function
of the device is reduced.
• Unwind the cable completely when using a cable drum.
• Do not use the power cords for purposes they are not intended
for. Protect the cable against heat, oil and sharp edges. Do jerk
on the power cable when pulling the plug from the socket.
• Check
connecting attachments
for defects or ageing before
using them.
• Never use defective
connecting attachments.
• When laying the connecting attachments, be sure that they do
get crushed or bent, and that the plug-and-socket connection
does not get wet.
• Do not use any
provisional electrical connections.
• Never bridge over
protective devices
or put them out of
operation.
• Only hook up the machine by means of a fault-
current circuit breacker: 30 mA!
A licensed professional electrician must make all
electrical
connections and repairs,
and observe local regulations in
doing so, especially those regarding protective measures.
The manufacturer or a company designated by the
manufacturer must attend to
the repair of all electrical
parts
on the machine.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer is
not liable for any damage or injury resulting from such
action.
START-UP
Observe all safety instructions
Setting up the machine:
• Set up and run the concrete mixer on a solid,
level
base
only (where it will not tip over).
• Keep the machine from
sinking
into the
ground or floor. Adhere to accident
prevention regulations (danger of tipping).
• When
setting up
the machine, make sure that the mixing drum
can be emptied without obstruction.
Switching on and off
Be sure that
- all protective devices are on the mixer and properly mounted.
- all safety instructions are adhered to.
• The on/off switch is located beneath the motor housing. Switch
the motor on and off
only at the switch.
• In the event of a power failure, the machine will switch off
automatically.
Press the switch again to restart the machine.
Motor protection
The motor is equipped
with a thermostat.
The thermostat
switches the motor off automatically in the event of overload
(overheating). The machine can be restarted after a
cooling-off
period.
MIXING
Mixer setting:
To make concrete or mortar, the mixing drum must be locked in a
specific position. Only the proper mixer setting ensures optimal
mixing results and smooth operation.Asetuspyörällä varustetut
betoninsekoittimet.
Concrete mixer with adjusting disc
Rotating level
Handwheel
Hold rotating lever or handwheel tightly while rotating.
loosen the rotating mechanism.
rotate the mixing drum up to the appropriate recess
for the material you are mixing.
→ allow rotating mechanism to lock into place.
I
I
PROF_IM_CONCRETE MIXER PROF 130MIX 130L 600W_ 21NN.indd 9
PROF_IM_CONCRETE MIXER PROF 130MIX 130L 600W_ 21NN.indd 9
1.6.2021 20.04.00
1.6.2021 20.04.00
