manualshive.com logo in svg

Pro-face PL-6930-T41, User Manual, Page: 105 / 175

Share
Download
Pro-face PL-6930-T41 User Manual Download Page 105

PL-6930 / PL-7930 Series User Manual

5-26

‹

Integrated Device Control Sub-Menu

Point the cursor to the [Integrated Device Control Sub-Menu] from the [ICH Control Sub-Menu] on the [Intel] 

screen and press the [Enter] Key, so that the following screen will be displayed.

USB-Device 29, F1 only / USB-Device 29, Function 7

Specifies an enabled/disabled state for the USB device. The choice is [Enabled] or [Disabled]. The factory 

default setting is [Enabled].

IDE-Device 31, Function 1

 Specifies an enabled/disabled state for the IDE device. The choice is [Enabled] or [Disabled]. The factory 

default setting is [Enabled].

AC97A-Device 31, Function 5

Specifies an enabled/disabled state for the AC97 Audio. The choice is [Enabled] or [Disabled]. The factory 

default setting is [Enabled].

Onboard LAN 1, 2

Specifies an enabled/disabled state for the Onboard LAN 1,2. The choice is [Enabled] or [Disabled]. The 

factory default setting is [Enabled].

Onboard Cardbus Controller

Specifies an enabled/disabled state for the PCMCIA Slot. The choice is [Enabled] or [Disabled]. The factory 

default setting is [Enabled].

Summary of Contents for PL-6930-T41
















































































































































































Reviews:

No comments