Pro-face PL-6930-T41 User Manual Download

Page: 75 / 175

PL-6930 / PL-7930 Series User Manual

4-8

Power cord specifications

Wiring

When connecting the Power Cord, use the following items when performing wiring. (The items are

manufactured by Phoenix Contact.)

Power Cable Size

0.75mm² to 2.5mm² (18AWG to12AWG)

Type of Cable Core

Single or Strand Wire

Cable Core Length

• Use copper conductors only.

• When using the Strand Wire, if the Conductor's end (individual) wires are not twisted

correctly, the end wires may either short against each other, or against an electrode.

Recommended Tool

SZS 0.6X3.5 (1205053)

Recommended Pin
Terminals

AI 0.75-10GY (3201288)
AI 1-10RD (3200182)
AI 1.5-10BK (3200195)
AI 2.5-12BUK (3200962)

Recommended Pin
Terminal Crimp Tool

CRIMPFOX ZA3 (1201882)

•

The power supply plug FKC-2.5/3-STF-5.08 is manufactured by Phoenix Contact.

For further details, please contact your local Phoenix Contact distributor.

[0.39

Summary of Contents for PL-6930-T41
















































































































































































Search results

Summary of Contents for PL-6930-T41

Reviews:

Related manuals for PL-6930-T41

Brands by name

Popular brands

Pro-face PL-6930-T41, User Manual

Search results

Summary of Contents for PL-6930-T41

Reviews:

Related manuals for PL-6930-T41

Brands by name

Popular brands