manualshive.com logo in svg

Power One AURORA, Installation And Operator'S Manual, Page: 25 / 65

Share
Download
Power One AURORA Installation And Operator'S Manual Download Page 25

Installation and operator’s manual 

     Page 25 of 65 

PVI-2000-OUTD-AU  Rev.: 1.0) 

 

 

 

 

 

 

NOTE

: According to the typical assembly diagram (see Fig.8) each array 

must be connected to Dc disconnect. An AC disconnecting mean provided 

with fuses or an over-current protection must be used to connect AURORA 
to the grid. Although the fuses are not mandatory, should you choose to use a 
Power-One-approved over-current protection, we recommend insetting them 
in the system. 
Recommended ratings for the Ac over-current protection device is maximum 
10A, 240V.  

 
 

 

9

 

Fig.10 General wiring diagram 

 
 

WARNING:

 always open the AC disconnect breaker to disconnect  

AURORA from the grid before opening the DC disconnect.

PV

 

Array

 

DC

 

Disconnect

 

Fuse rating

 

10A, 600V

 

AC

Disconnect

 

Fuse rating

10A 240Vac

 

Wire in accordance with

 

NEC Section 690 and

 

applicable local codes

 

Load

 

Center

Grid

AUR

O

R

A

 

Summary of Contents for AURORA


































































Reviews:

No comments