manualshive.com logo in svg

Power One AURORA, Installation And Operator'S Manual, Page: 21 / 65

Share
Download
Power One AURORA Installation And Operator'S Manual Download Page 21

Installation and operator’s manual 

     Page 21 of 65 

PVI-2000-OUTD-AU  Rev.: 1.0) 

 

 

 

 

 

3.4

 

Wall Mounting 

AURORA should be mounted in a vertical position as shown in figure 7. 
 

  NOTE: 

AURORA ratings are based on a vertical mounting position.

 

Although it is possible to mount AURORA in a tilted position, the 

thermal performance in that case may be de-rated. In any case avoid 
mounting AURORA with the front plate rotated, always make sure that 
the fins of the front heatsink are vertical. 
 
To facilitate wall mounting a reference drawing is provided in the package (Fig.6). 
Use the drawing to locate the holes on the wall. A set of standard expansion 
stainless steel screws is included in the package for use in mounting the AURORA 
to a masonry wall. In case of different materials make sure to select the proper 
mounting hardware. Always use stainless steel mounting hardware, if the supplied 
hardware is not used. 
The clearance hole in the mount bracket is 8 mm. 
 

 

 

Fig. 6 Wall mounting diagram 

Summary of Contents for AURORA


































































Reviews:

No comments