manualshive.com logo in svg

Pontiac 2001 Bonneville, Owner'S Manual

Share
Download
Pontiac 2001 Bonneville Owner'S Manual Download Page 130

2-63

2. Decide which one of the three channels you want to

program. Hold the end of the hand

-

held transmitter

about 2 to 5 inches (5 to 13 cm) away from the
surface of the HomeLink Transmitter so that you can
still see the indicator light.

3. Using both hands, press the hand

-

held transmitter

button and the desired button on the HomeLink
Transmitter. Continue to press both buttons 
through Step 4.

4. Hold down both buttons until you see the indicator

light on the HomeLink Transmitter flash slowly and
then rapidly. The rapid flashing indicates that the
HomeLink Transmitter has been programmed.
Release both buttons once the indicator light starts to
flash rapidly.

If you have trouble programming the HomeLink
Transmitter, make sure that you have followed the
directions exactly as described. The HomeLink
Transmitter may not work with older garage door
openers that do not meet current Federal Consumer
Safety Standards. If you cannot program the transmitter
after repeated attempts, refer to “Rolling Code
Programming” later in this section or contact the
HomeLink Transmitter manufacturer 
at 1

-

800

-

355

-

3515.

Be sure to keep the original hand

-

held transmitter 

in case you need to erase and reprogram the 
HomeLink Transmitter.

Canadian Owners: During programming, the
hand

-

held transmitter may automatically stop

transmitting after one or two seconds. In this case, 
you should press and re

-

press the button on the

hand

-

held transmitter every two seconds without ever

releasing the button on the HomeLink Transmitter.
Release both buttons when the indicator light on the
HomeLink Transmitter begins to flash rapidly.

Summary of Contents for 2001 Bonneville






























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands