manualshive.com logo in svg

Pontiac 2001 Bonneville, Owner'S Manual

Share
Download
Pontiac 2001 Bonneville Owner'S Manual Download Page 118

2-51

Inadvertent Power Battery Saver

This feature is designed to protect your vehicle’s battery
against drainage from the interior lamps, trunk lamp,
glove box lamp or cigarette lighters. When the ignition
is turned off, the power to these features will
automatically turn off after 10 minutes. Power will be
restored for an additional 10 minutes if any door is
opened, the trunk is opened or the courtesy lamps are
turned on. To restore power back to the cigarette lighters
the ignition must be turned back to ON.

Battery Load Management

The battery load management feature is designed to
monitor the vehicle’s electrical load and determine when
the battery is in a heavy discharge condition. During
times of high electrical loading, the engine may idle at
higher revolutions per minute (rpm) than normal to
make sure the battery charges. High electrical loads may
occur when several of the following are on: headlamps,
high beams, fog lamps, rear window defogger, high
blower fan, heated seats and engine cooling fans.

If your vehicle’s battery remains in a heavy discharge
condition for a long period of time, the blower fan, rear
defogger, heated seats and heated mirrors will be
disabled and the DIC will display BATTERY SAVER
ACTIVE. This can happen either under long periods of
idling or low speed driving with high electrical loading,
or in the event of a charging system fault.

Monitor the battery voltage when in the BATTERY
SAVER ACTIVE mode.
D If the voltmeter remains in the red area (below 11 volts) 

when driving then have the charging system 
serviced immediately.

D If the voltage increases above 12 volts then the battery

needs to be recharged. Try driving on the highway
with as few electrical accessories on as possible.

Mirrors

Inside Day/Night Manual Rearview Mirror

When you are sitting in a comfortable driving position,
adjust the mirror so you can see clearly behind your
vehicle. Grip the mirror in the center to move it up or
down and side to side. The day/night adjustment allows
you to adjust the mirror to avoid glare from the lamps
behind you. Push the tab away from you for daytime
use; pull it toward you for night use.

Summary of Contents for 2001 Bonneville






























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands