Ponsel ACTEON 2020 Redox-Temperature User Manual Download Page 29

Page: 29 / 57

User manual

PONSEL

Ref.: NOTICE_ACTEON_2020_v003

V : 003

29/57

6.1.5 Temperature sensor slope adjustment

If you observe a small measurement error, you may only adjust the slope of your sensor by carrying out the
following procedure:

CALIBRATION

SENSORS CALIBRATION

OPR SENSOR

Gain adjust

Complete calibration

Theoretical calibration

TEMPERATURE SENSOR

Gain adjust

Complete calibration

Theoretical calibration

ENTER: Validate the choice

Use the

and

keys to select

the type of calibration and the
probe to be calibrated.

Select the

Gain adjust

menu and press ENTER.

Use the

and

keys to adjust the

ambient water temperature value.

Press the ENTER key to confirm slope
adjustment.

CALIBRATION

TEMPERATURE SENSOR

Immerse the sensor in
water at ambient temperature

Standard:
Measure:

°C
°C

20.00

20.20

WAIT: Nonstable measurement

AWAIT MEASUREMENT STABILISATION

Immerse the sensor in water at ambient temperature.

ESC: Leave the current slope
ENTER: Validate the new slope

Summary of Contents for ACTEON 2020 Redox-Temperature


























































Search results

Summary of Contents for ACTEON 2020 Redox-Temperature

Reviews:

Related manuals for ACTEON 2020 Redox-Temperature

Brands by name

Popular brands

Ponsel ACTEON 2020 Redox-Temperature, User Manual

Search results

Summary of Contents for ACTEON 2020 Redox-Temperature

Reviews:

Related manuals for ACTEON 2020 Redox-Temperature

Brands by name

Popular brands