Ponsel ACTEON 2020 Redox-Temperature User Manual Download Page 25

Page: 25 / 57

User manual

PONSEL

Ref.: NOTICE_ACTEON_2020_v003

V : 003

25/57

6.1.3 Returning to REDOX measurement theoretical calibration:

Theoretical calibration is carried out using the theoretical coefficients.
Follow the instructions below to carry out theoretical calibration:

20.00

°C

-24 hrs

290

MEASUR
E

INFO

CONF

HIST CAL

LOG

MEAS

Mode1 R1
R2

ACTEON 2020 ORP

200

300

CALIBRATION

SENSORS CALIBRATION

ORP SENSOR

Gain adjust

Complete calibration

Theoretical calibration

TEMPERATURE SENSOR

Gain adjust

Complete calibration

Theoretical calibration

ENTER: Validate the choice

Use the

and

keys to select

the type of calibration and the
probe to be calibrated.

Select the

Theoretical calibration

menu and

press ENTER.

THEOR CAL

Indicates that the device has
been calibrated with the
theoretical coefficients.

Use the

and

keys to select the

procedure confirmation.

CALIBRATION

THEORETICAL CALIBRATION

Esc: Cancel the procedure

Enter: Validate the choice

ATTENTION, you will erase your
calibration coefficients to return to
the theoretical coefficients!

Yes

Select

Yes

and press ENTER to return to the

theoretical coefficients.

Summary of Contents for ACTEON 2020 Redox-Temperature


























































Search results

Summary of Contents for ACTEON 2020 Redox-Temperature

Reviews:

Related manuals for ACTEON 2020 Redox-Temperature

Brands by name

Popular brands

Ponsel ACTEON 2020 Redox-Temperature, User Manual

Search results

Summary of Contents for ACTEON 2020 Redox-Temperature

Reviews:

Related manuals for ACTEON 2020 Redox-Temperature

Brands by name

Popular brands