Polycom ViewStation SP User Manual Download Page 23 | Manualshive

Page: 23 / 192

background image

Chapter 1

Getting Started

©

Polycom, Inc.

5

ViewStation SP User Guide

Note

If you connect less than three ISDN lines to the Triple BRI
network interface module, the status indicators shown on
the TV monitor are displayed in red.

For more ISDN information, refer to the Appendix D, “ISDN
Information,” on page 151.

ViewStation SP128

Complete the following steps to connect the ViewStation SP128 to
an ISDN network:

1.

Connect the green tipped RJ-45 cable to the green RJ-45 port
on the back of the ViewStation SP.

2.

Connect the opposite end of the green tipped cable to an ISDN
wall jack.

For more ISDN information, refer to the Appendix D, “ISDN
Information,” on page 151

.

Once the interface is properly connected, the ViewStation SP is
ready to be configured for EtherNet LAN connectivity.

Connecting the ViewStation SP to an Ethernet LAN

The following describes how to connect the ViewStation SP to an
Ethernet LAN. Before setting up the ViewStation SP, ensure all the
network connectivity issues are tested and resolved.

ViewStation SP384

Complete these steps to connect the ViewStation SP384 with to an
Ethernet LAN network:

1.

Connect the orange tipped RJ-45 cable to the RJ-45 port
labeled LAN on the back of the ViewStation SP.

2.

Connect the opposite end of the orange tipped RJ-45 cable with
the orange tip to an Ethernet LAN wall jack.

3.

If the LAN wall jack is active, a green light appears on the orange
RJ-45 port on the back of the ViewStation SP384.

«
...
21
22
23
24
25
...
»

Summary of Contents for ViewStation SP

































































































































































































Reviews:

No comments

Related manuals for ViewStation SP

Brand: Zenith Pages: 24

Airedale Sentinel

Brand: Modine Manufacturing Pages: 2

Brand: Polycom Pages: 10

Brand: Daewoo Pages: 27

Brand: Velux Pages: 24

Brand: SIMARINE Pages: 22

Brand: ZheJiang Libiao Robotics Pages: 10

Brand: Vivax Pages: 68

Brand: Technics Pages: 14

Brand: LAIA Pages: 9

Brand: MAJORITY Pages: 32

Brand: Yaesu Pages: 39

Zynq UltraScale+

Brand: Xilinx Pages: 86

Brand: AbleNet Pages: 8

Brand: Discount Car Stereo Pages: 5

Brand: New Rock Technologies Pages: 71

Brand: Foxtech Pages: 63

Brand: Pioneer Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands