Polyaire airtouch Installer Manual Download Page 38 | Manualshive

Page: 38 / 68

background image

38

Firmware Version Before 2.3

Important: It’s strongly recommended NOT to use the Panasonic wall controller
and the gateway at the same time. It may damage the indoor PCB in long term
and in extreme weather conditions.

1. Wire AirTouch 4, gateway and AC indoor as per diagram below and leave the

dipswitches on the gateway at their default position. Make sure all wires are
connected properly.

2. Initialise the AC Unit with Panasonic AC Wall Controller connected. The

Panasonic wall controller can be wired to R1 and R2 in parallel with the
gateway

3. Remove the Panasonic wall controller after commissioning

4. If AirTouch 4 sensors are to be used for AC temperature control, go to AirTouch

4 AC setting and select proper sensor/combination.

(657213) Commissioning notes

Wiring Diagrams contd.

«
...
36
37
38
39
40
...
»

Summary of Contents for airtouch





































































Reviews:

No comments

Related manuals for airtouch

Brand: Zetkama Pages: 6

Brand: Facility Explorer Pages: 4

Brand: Hankscraft Runxin Pages: 53

Brand: Panasonic Pages: 45

Brand: ZETRON Pages: 3

Brand: ADEMCO Pages: 2

Brand: Samson Pages: 78

Brand: OJ Electronics Pages: 8

Brand: OJ Electronics Pages: 112

Brand: OJ Pages: 17

Brand: York Pages: 20

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: R82 Pages: 11

Brand: National Instruments Pages: 72

Brand: National Instruments Pages: 41

MAGNUM ALERT 3000 FIRE ALARM

Brand: NAPCO Pages: 2

GA Industries 930-DT

Brand: Vag Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands