Polyaire airtouch Installer Manual Download Page 15 | Manualshive

Page: 15 / 68

background image

15

There are two sets of settings, the installer’s and user’s. In the installer’s settings,
the followings can be set: parameters, balancing, sensors, spill, grouping, service
and AC. These settings are protected by a password which has default value

Polyaire

but can be changed. Touching Installer’s button in the Settings list will

bring up password input page. After inputting the correct password, installer’s
setting page will come up. In the user’s settings which are discussed in User’s
Manual, the followings can be set: owner name, date/time, group name, WiFi,
turbo group, temperature display, touch tone, child lock and temperature alert.

5. Recommended Commissioning Procedure

Recommended Commissioning Procedure

«
...
13
14
15
16
17
...
»

Summary of Contents for airtouch





































































Reviews:

No comments

Related manuals for airtouch

Brand: XBOX Pages: 2

C-NaviGator III

Brand: C-Nav Pages: 20

Brand: Gardner Denver Pages: 22

Brand: B&G Pages: 2

Brand: Häfele Pages: 2

Brand: Häfele Pages: 24

MorphoAccess SIGMA Extreme Series

Brand: Safran Pages: 79

Brand: Lawler Pages: 5

Brand: Madas Pages: 6

Brand: Madas Pages: 11

Brand: R82 Pages: 89

Brand: OJ Electronics Pages: 8

Brand: OJ Electronics Pages: 112

Brand: OJ Pages: 17

Tissue-Tek TEC 6

Brand: Sakura Seiki Pages: 6

Z3-DM8107-SDI-RPS

Brand: Z3 Technology Pages: 73

Brand: Z-Wave Pages: 14

Brand: Z-Wave.Me Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands