Polyaire airtouch Installer Manual Download Page 56 | Manualshive

Page: 56 / 68

background image

56

NOTE: This gateway will only work with units which have 16kW and above

capacity with MWR-WE10N wall controller (NASA protocol). Samsung wall

controller cannot be used at the same time.

1. Wire AirTouch, gateway and AC indoor as per diagram and leave the

dipswitches on the gateway at their default position. Make sure all wires are
connected properly.

2. Initialise the AC Unit. If AirTouch 4 sensors are used for AC temperature control:
•

Settings on the AirTouch 4: choose from Control Thermistor list in the
Installer’s AC Setup.

•

Settings from the Samsung wall controller: Go to Installation/Service Modes
by pressing and holding ESC and Set buttons together, find Main Menu 1,
Submenu 2, and then set Data bit 1 to 1. After the setting, remove the
Samsung wall controller and use the gateway only.

•

Restart the AC and gateway first and then power up AirTouch. Or power
them up at the same time.

NASA (657229) Commissioning Notes

Wiring Diagrams contd.

«
...
54
55
56
57
58
...
»

Summary of Contents for airtouch





































































Reviews:

No comments

Related manuals for airtouch

Brand: E-fly Pages: 16

Brand: 7bit Pages: 2

Brand: Jafar Pages: 15

Brand: Jeep Pages: 32

Brand: Accel Pages: 8

Brand: H3C Pages: 69

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Brand: Omnex Pages: 9

Brand: Omegon Pages: 6

Brand: WATERLOO Pages: 8

Brand: Eaton Pages: 10

Brand: Idemia Pages: 29

MultiConnect Dragonfly MTQ-MNA1-B01

Brand: Multitech Pages: 45

Brand: CALEFFI Pages: 10

EZ-ZONE PM L AAAAB Series

Brand: Watlow Pages: 30

Bilge Pump Control Panel

Brand: SPXFLOW Pages: 14

Brand: Danfoss Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands