Polyaire airtouch Installer Manual Download Page 29 | Manualshive

Page: 29 / 68

background image

29

5.9.4 Configure AC Fan Speed Options

AirTouch 4 can automatically recognise the total fan speed options from the
indoor unit in most cases. In rare cases, the installer may need to manually set the
fan speed options to match the actual fan speed options of the AC unit. First tick
the fan speed names and then change the fan speed matching number. As in the
image below, the Low fan speed number may be changed to 1, Medium to 2, High
to 3 and Powerful to 4.

Touch Save & Back to save.

5.9.5 Control Temperature Offset

The measured temperature from the selected control thermistor can be offset to
suit the situation. It’s up to the installer to choose the value.

Setting up AC Control contd.

«
...
27
28
29
30
31
...
»

Summary of Contents for airtouch





































































Reviews:

No comments

Related manuals for airtouch

Brand: GE Pages: 425

Brand: Sole Diesel Pages: 8

Brand: Wavetec Pages: 17

Brand: Calsense Pages: 9

Smart Controller

Brand: MaestroHome Pages: 10

Brand: Hama Pages: 7

Brand: Hama Pages: 44

Brand: RadioMaster Pages: 10

Brand: K&K Pages: 6

MachXO5-NX Development Kit

Brand: Lattice Semiconductor Pages: 2

Brand: Vacon Pages: 50

Brand: V2 Pages: 116

Brand: V2 Pages: 8

Brand: V2 Pages: 25

Brand: V2 Pages: 124

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brand: KEENZ Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands