Polyaire airtouch Installer Manual Download Page 54 | Manualshive

Page: 54 / 68

background image

54

1. Wire AirTouch 4, gateway and AC indoor as per diagram below and leave the

dipswitches on the gateway at their default position. Make sure all wires are
connected properly.

2. Check the temperature compensation value setting (SW6 switch) on the indoor

PCB and make sure its value is set to EEPROM DEFAULT as per the instructions
on the wiring label at the back of the electrical box cover.

3. In default, AC will use its own return air sensor as control sensor. Installers can

set the AC control thermistor to an AirTouch 4 sensor by going to AC setup in
Installer’s Settings of AirTouch 4.

4. If the sensor on the AC wall controller is used for AC control (Follow Me feature

on the AC wall controller), please: Press the Follow Me button on the wall
controller to activate Follow Me. The displayed value for home temperature will
be the measured temperature where the AC wall controller installed.

(657222) Commissioning Notes

Wiring Diagrams contd.

«
...
52
53
54
55
56
...
»

Summary of Contents for airtouch





































































Reviews:

No comments

Related manuals for airtouch

Brand: Valve Concepts Pages: 16

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 10

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: Quectel Pages: 23

Brand: Quectel Pages: 79

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 10

Brand: Danfoss Pages: 20

EtherNetIP ControlPlex CPC12EN

Brand: E-T-A Pages: 28

Brand: S&P Pages: 17

Brand: S&S Northern Pages: 9

Brand: Vanderbilt Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands