Polaris Sportsman 570 EFI Owner'S Manual Download | Manualshive

Page: 41 / 148

background image

39

FEATURES AND CONTROLS

Instrument Cluster

Digital/Analog Gauge

Rider Information Center

Clock Mode

Tip:

The clock must be reset any time the battery has been disconnected or
discharged.

1. Turn the key to the ON position. Use the MODE button to toggle to

the odometer display.

2. Press and

hold

the MODE button until the hour segment flashes.

Release the button.

3. With the segment flashing, tap the MODE button to advance to the

desired setting.

4. Press and

hold

the MODE button until the next segment flashes.

Release the button.

5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments.

After completing the 1-minute segment, step 4 will save the new
settings and exit the clock mode.

6. Turn the key to the OFF position.

Odometer Mode

The odometer records and displays the distance traveled by the ATV.

Trip Meter Mode

The trip meter records the distance traveled by the ATV if reset before
each trip. To reset, select the trip meter mode. Press and hold the MODE
button until the meter resets to zero. In the Rider Information Center, the
trip meter display contains a decimal point, but the odometer displays
without a decimal point.

Hour Meter Mode

This mode logs the total hours the engine has been in operation.

«
...
39
40
41
42
43
...
»

Summary of Contents for Sportsman 570 EFI





















































































































































Reviews:

No comments

Related manuals for Sportsman 570 EFI

2005 Ranger 4x4

Brand: Polaris Pages: 121

BOSS RT FATBOY 1026RT RR

Brand: Meyer Pages: 44

2014 SNO PRO 500

Brand: Arctic Cat Pages: 90

Brand: Arctic Cat Pages: 68

Brand: Arctic Cat Pages: 80

Brand: Arctic Cat Pages: 76

2010 1000 H2 TRV

Brand: Arctic Cat Pages: 104

Brand: SILLA Pages: 52

Brand: E-Z-GO Pages: 80

Brand: Camoplast Pages: 55

MARSH MASTER 2015

Brand: COAST MACHINERY Pages: 59

BIG BEAR 4X4 YFM400FWNM

Brand: Yamaha Pages: 167

Sportsman 800 Efi 2005

Brand: Polaris Pages: 309

Can-Am Defender DPS HD10

Brand: BRP Pages: 244

BOMBARDIER DS250 2006

Brand: BRP Pages: 284

Brand: Taylor-Dunn Pages: 130

2001 TRX250EX Sportrax 250EX

Brand: Honda Pages: 153

Fourtrax TRX300

Brand: Honda Pages: 353

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands