Polaris Sportsman 570 EFI Owner'S Manual Download Page 79

Page: 79 / 148

MAINTENANCE

Periodic Maintenance Chart

Maintenance Chart Key

WARNING!

Improperly performing the procedures marked with a

“D”

could

result in component failure and lead to serious injury or death. Have an
authorized POLARIS dealer perform these services.

Perform all services at whichever maintenance interval is reached first.

Perform these procedures more often for vehicles subjected to severe use.

Emission-Related Service

Have an authorized POLARIS dealer perform these services.

Symbol

Description

Perform these operations more often for vehicles subjected to severe use.

Emission-related service (failure to conduct this maintenance will not void
the emissions warranty but may affect emissions)

Have an authorized POLARIS dealer perform these services.

Item

Maintenance Interval

(whichever comes first)

Remarks

Hours Calendar

Miles

(Km)

Steering

Pre-Ride

Make adjustments as need
ed. See Pre-Ride Checklist
on page 48.

Front suspension

Rear suspension

Tires

Brake fluid level

Brake lever travel

Brake system

Wheels/fasteners

Frame fasteners

Engine oil level

Winch (if equipped)

See pages 63-74

Air filter, pre-filter

Daily

Inspect; clean often; replace
as needed

Air box sediment
tube

Daily

Drain deposits when visible

Coolant

Daily

Check level daily, change
coolant every 2 years

Power steering unit
(if equipped)

Daily

Inspect daily; clean often

Headlight/taillight/
worklight

Daily

Check operation; apply
dielectric grease if replacing
lamps

Summary of Contents for Sportsman 570 EFI





















































































































































Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands

Polaris Sportsman 570 EFI, Owner'S Manual

Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands