Polaris Sportsman 570 EFI Owner'S Manual Download

Page: 133 / 148

131

SPECIFICATIONS

* Based on EU Directive 76/432/EC

SPORTSMAN 570 EFI/EPS

Gross Vehicle Weight

1200 lbs. (544 kg)

Maximum Weight Capacity

485 lbs. (220 kg) (operator, cargo, accessories)

Dry Weight

702 lbs. (318.4 kg) (570 EFI)
713 lbs. (323.4 kg) (570 EPS)

Fuel Capacity

4.5 gal. (17 l)

Engine Oil Capacity

2 qts. (1.9 l)

Transmission Oil Capacity

32 oz. (948 ml)

Demand Drive Fluid Capacity

9 oz. (265 ml)

Coolant Capacity

2.7 qts. (2.5 l)

Front Rack/Box Capacity

90 lbs. (40.8 kg)

Rear Rack/Box Capacity

180 lbs. (81.6 kg)

Receiver Hitch Tongue
Capacity

120 lbs. (54 kg) (Rear rack capacity and tongue
weight not to exceed 180 lbs./81.6 kg)

Hitch Towing Rating

1225 lbs. (555.7 kg)

Unbraked Trailer Towing
Capacity*

1786 lbs. (810 kg)

Overall Length/Width/Height

83 in. (211 cm) / 48 in. (122 cm) / 48 in. (122 cm)

Wheelbase

50.5 in. (128.3 cm)

Ground Clearance

11 in. (28 cm)

Minimum Turning Radius

65 in. (165 cm) unloaded

Engine

Dual overhead cam, 4 valve 4 stroke single cylinder

Displacement

567 cc

Bore x Stroke

99mm x 73.6mm

Alternator Output

560 W @ 7000 RPM

Compression Ratio

10:1

Starting System

Electric

Fuel System

Electronic Fuel Injection

Ignition System

ECU

Spark Plug / Gap

RG6YC / 0.7-0.8 mm

Lubrication System

Wet Sump

Driving System Type

Automatic PVT (POLARIS Variable Transmission)

Front Suspension

MacPherson strut with 8.2" (21 cm) travel

Rear Suspension

Progressive rate with 9.5" (24 cm) travel

Shift Type

H/L/N/R/P

Summary of Contents for Sportsman 570 EFI





















































































































































Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands

Polaris Sportsman 570 EFI, Owner'S Manual

Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands