Polaris Sportsman 570 EFI Owner'S Manual Download | Manualshive

Page: 119 / 148

background image

117

MAINTENANCE

Camber and Caster

The camber and caster are non-adjustable.

Rear Spring

The rear shock absorber spring is adjusted
by rotating the cam either clockwise or
counter-clockwise to increase or decrease
spring tension.

Accessory springs are available through
your POLARIS dealer.

Handlebars

The handlebars can be adjusted for rider
preference.

WARNING!

Improper adjustment of the

handlebars or incorrect torquing of the adjuster
block tightening bolts can cause limited steering
or loosening of the handlebars, resulting in loss
of control and serious injury or death. Follow the
adjustment procedures exactly, or see your
POLARIS dealer for service.

1. Remove the upper headlight

pod.

2. Loosen the four handlebar

bolts.

3. Adjust the handlebar to the

desired height.

4. Be sure the handlebars do not

contact the gas tank or any
other part of the machine when
turned fully to the left or right.

5. Torque the front two bolts to

10-12 ft. lbs. (14-17 Nm), then
torque the rear two bolts. A
gap of up to 1/8" (3 mm) will
remain at the rear of the clamp blocks.

High

Tension

Low

Tension

Cam

Handlebar

Bolts

«
...
117
118
119
120
121
...
»

Summary of Contents for Sportsman 570 EFI





















































































































































Reviews:

No comments

Related manuals for Sportsman 570 EFI

Brand: Jayco Pages: 87

BOSS RT FATBOY 1026RT RR

Brand: Meyer Pages: 44

CU-48 OFF-ROAD SERIES

Brand: Crown Pages: 8

Brand: CF MOTO Pages: 365

Brand: Arctic Cat Pages: 72

ATV ELECTRIC POWERED

Brand: MINIMOTO Pages: 31

Brand: Realtree Pages: 12

Brand: Landoll Pages: 72

Brand: GAS GAS Pages: 60

Brand: Taylor-Dunn Pages: 188

Brand: Burley Pages: 16

FXNytro FX10RTRSZ

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 134

Brand: Taylor-Dunn Pages: 233

Brand: Taylor-Dunn Pages: 266

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands