Polaris Sportsman 570 EFI Owner'S Manual Download

Page: 112 / 148

110

MAINTENANCE

PVT System

When to Use Low Range and High Range

PVT Drying

There may be some instances when water is accidently ingested into the
PVT system. Use the following instructions to dry it out before
operating.

1. Position the vehicle on a level surface.

2. Remove the drain plug. Allow the water to drain completely.

Reinstall the drain plug.

3. Start the engine. Place the transmission in PARK.

4. Apply varying throttle for 10-15 seconds to expel the moisture and

air-dry the belt and clutches. Do not hold the throttle wide open for
more than 10 seconds.

5. Allow the engine RPM to settle to idle speed, then shift the

transmission to the lowest available range.

6. Test for belt slippage. If the belt slips, repeat the process.

7. Take the vehicle to your dealer for service as soon as possible.

Condition

Range to Use

Operating at speeds less than 7 MPH (11 km/h)

Low

Towing heavy loads

Low

Operating in rough terrain (swamps, mountains, etc.)

Low

Operating at speeds greater than 7 MPH (11 km/h)

High

Summary of Contents for Sportsman 570 EFI





















































































































































Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands

Polaris Sportsman 570 EFI, Owner'S Manual

Search results

Summary of Contents for Sportsman 570 EFI

Reviews:

Related manuals for Sportsman 570 EFI

Brands by name

Popular brands